General Fault Analysis and Troubleshooting of Fuel Tanker Trucks

Foton Auman 18000 Liters Fuel Tanker Truck

Fuel Tanker Truck Antifreeze Replacement Requirements

Fault Phenomenon Cause Analysis Troubleshooting Method
Cannot suction oil, or suction is too low 1. Engine speed too low 1. Increase engine speed
2. No priming oil in the pump 2. Add priming oil
3. Air leak in suction pipe, low vacuum 3. Seal leak points, increase vacuum
4. Suction pipe blocked 4. Remove blockage
5. The three-way ball valve in the suction pipe is incorrectly positioned 5. Turn the valve handle to align the color mark with the closed port
6. Coarse filter severely clogged 6. Clean the coarse filter
7. Oil pump worn or damaged 7. Repair or replace the oil pump
8. The intake valve in the breather valve cannot open 8. Repair the breather valve (to prevent tank collapse due to vacuum)
Cannot discharge oil from the tank 1. Valve not opened or not fully opened 1. Open valve
2. Water in the sediment trap is frozen 2. Use steam to melt ice; open the drain to release water
3. Dirt in the tank is blocking the outlet 3. Clean out dirt
4. Breather valve clogged, poor air intake 4. Repair breather valve
Power take-off is not working properly 1. Gear wear or a thick gasket causes abnormal noise 1. Replace the gear or use a thinner gasket
2. Gasket too thin, gears damaged, or housing cracked 2. Use a thicker gasket
3. PTO fork damaged or cylinder malfunction 3. Replace the fork or repair the cylinder/piston
4. Pneumatic valve damaged 4. Repair or replace pneumatic valve
5. Oil seal or gasket damaged 5. Repair or replace oil seal/gasket
Severe vibration in the drive shaft 1. Drive shaft bent 1. Straighten the drive shaft
2. Poor dynamic balance 2. Perform a dynamic balance test
3. Worn PTO or pump speed-up box bearings 3. Replace the relevant bearing
4. Universal joint bolts are loose 4. Tighten bolts
5. Incorrect installation of universal joints 5. Adjust the direction of the universal joints
6. Universal joint/sliding spline worn 6. Replace the joint or entire drive shaft
Oil leakage from tank/piping 1. Porosity or pinholes in welding 1. Pressurize tank (36 KPa), apply soapy water to locate and weld leaks
2. Tank torn due to bumps on rough road 2. Same as above
Ball valve leakage 1. End cap bolts loose 1. Tighten bolts
2. Ball valve base adjustment seat is loose 2. Tighten the adjustment seat
3. Sand holes or porosity in the valve body 3. Replace the ball valve
4. The “O” ring at the valve stem is damaged 4. Replace the “O” ring
Breather valve malfunction 1. Intake/exhaust springs failed 1. Replace the spring
2. Intake/exhaust valves stuck 2. Reassemble and remove obstructions
Flow meter failure 1. Debris stuck in the oval rotor 1. Clean debris
2. Oval rotor damaged 2. Replace rotor
Proper antifreeze replacement is essential for the safe and efficient operation of fuel tanker trucks, especially in extreme temperatures. Antifreeze, also known as coolant, helps regulate engine temperature, prevents freezing in cold climates, and protects against overheating in warm conditions. For fuel tanker trucks that transport flammable liquids, maintaining optimal engine performance is critical to ensuring operational safety and preventing breakdowns.

Replacement Requirements:

  1. Recommended Interval: Antifreeze should typically be replaced every 1–2 years or according to the manufacturer’s maintenance schedule. Heavy-duty fuel tanker trucks may require more frequent checks due to longer operational hours and heavier engine loads.
  2. Type of Antifreeze: Use only manufacturer-approved antifreeze types (e.g., ethylene glycol or extended life coolant) compatible with the truck’s engine and materials to avoid corrosion or seal damage.
  3. System Flushing: Before replacing the antifreeze, the cooling system must be flushed to remove any residues, rust, or contaminants that could impair cooling efficiency.
  4. Proper Mixture: The coolant should be mixed with distilled water in the recommended ratio—commonly 50:50—unless pre-mixed coolant is used.
  5. Inspection During Replacement: During antifreeze replacement, inspect hoses, radiator, water pump, and thermostat for wear or leaks. Any faulty components should be repaired or replaced.
  6. Disposal: Used antifreeze must be disposed of according to local environmental regulations to prevent contamination.

Regular antifreeze replacement not only extends engine life but also ensures the fuel tanker operates safely under various environmental conditions.

Foton Auman 18000 Liters Fuel Tanker Truck (2)

Leave a Reply

Your email address will not be published. Required fields are marked *