8,000Liters Vacuum Tank Truck
- Item No:ZK9513W801B
- Model:CSC5120GXWD4
Power:190HP - Capacity:8,000L
Driving Mode:4 x 2
- Price: $36000
I am interested in this truck /trailer
- Overall Views : 2449
- Read all reviews Submit your review
- Share with friends:
Vacuum Truck Model: CSC5120GXWD4
Nominal Vacuum Tank Capacity: 8,000Liters
Nomial Loading Capacity of Truck: 7,300kg
1: Vacuum Truck Chassis Specification
1.1 Main Application
CSCTRUCK Vacuum truck is designed to collect, by suction, and transport sewage and sludge. Truck mounted with sewage pump consists of a sub frame connected to the truck chassis, a cylindrical tank, a hydraulically opening full diameter tailgate and the vacuum system powered by the PTO.
The vacuum truck is intended for vacuum cleaning of cesspools and transportation of fecal liquids to disposal area. Special equipment must consist of the tank, driven vacuum pump, signal-safety device, receiving manhole with suction hose, control valves on the pipeline, platforms and additional electrical equipment. Filling of the tank is carry out under the impact of vacuum which is produced by vacuum pump, tank gravity discharge or air pressure from the vacuum pump.
1.2 Principal Features
a.The equipment to be supplied under this contract is new and of the most current model 2013
b.Left-hand drive
c.Power asssitance steering
d.4x2, rear axle drive
e.Three (3) persons seating capacity
f.Water-cooled, four-stroke cycle diesel engine
g.Flywheel horsepower: 190hp@2500rpm
h.Hydraulic lifting/tipping gear with control system
i.Lifting capacity: 7,300 kg
j.Power-take-off to drive the hydraulic pump
k.Payload of fully equipped and loaded truck (including container) : 12,500kg minimum
l.Rear axle rating: 15,000kg approx.
m.GVW: 16,000kg minimum
n.Gradability (max. restart gradient off highway at GVW): 30%
o.Ground clearance: 270 mm
p. Overall dimension : 7200mm×2400mm×3300mm
1.3 Engine
Water-cooled,four-stroke cycle diesel engine with the following features:-
a. Vertical ,in line
b. Flywheel horsepower:190hp@2500rpm
c. Flywheel horse power 140(kw) /2500(rpm), torque and engine speed 670(N.m)/1300-1500(rpm)
as well as aver-age fuel consumption 16L/100km .h ;Engine manufactuer Dongfeng Cummins, model:B190 33
d. Lubrication: forced lubrication
e. Lubricant filtration:filter
i. Full-flow and by-pass
ii. Replaceable element/ cartridge;
f. Lubricant cooler equipped
g.Fuel System: Direct Injection
h.Fuel filtration:filter
i.Primary and Secondary
ii.Replaceable element/ cartridge
i.Fuel-water separator required in fuel line
j.Fuel tank capacity: 160 litres
k.Fuel tank cap with security lock
l. Specify the following:
i.Mechanical fuel injection pump
ii.Mechanical Governor
m. Cooling System: Heavy duty pressurised water cooling with sufficient capacity to function in the specified ambient temperature
n. Radiator fins and tubes to be made of copper
o. Radiator protection grille
p. Natural aspiration
q. Heavy-duty ,dry-type air cleaner with replaceable elements
r. Pre-cleaner fixed.
s. Pre-ignition heating system
1.4 Clutch
a. Heavy duty, dry single plate; hydraulic actuation .
b. Specify diameterΦ395mm
1.5 Transmission,PTO and Drive Line
a.Constant speed synchromesh gearbox
b.Floor-mounted manual shift gear lever
c. 5 speed forward and 1 speed reverse
d.Max. geared speed: 95km/h
e.Manufacturer's standard PTO box is provided
f.4 x 2 WD truck; single rear axle drive
g.Gradability (max restart gradient off highway at GVW): 30%
1.6 Chassis Frame
a.Heavy-duty all steel constructed frame to be reinforced with cross members
b.Front towing hook
c.Front steel bumper
d.Front fenders have mudflaps
e. Full rear steel mudguards with mud flaps
f. Specify the following:
i.Frame sectional modulus :250mm× 80mm× (7+4)mm
ii.Tensile strength of frame material Q235A high strength steel.
1.7 Axles
a.Torque proportioning differ-ential rear axle with foot-operated or otherwise differential lock
b.Hub reduction floating rear axle
c. Rear axle rating: 10,000kg approximately
d. Rigid I beam front axle
1.8 Suspension
a.Front:
i. Heavy duty semi-elliptic leaf spring
ii.Double acting telescopic shock absorbers
b.Rear:
i.Heavy duty semi-elliptic leaf spring
ii.Second stage helper spring
c.Sring details:Front 8pcs /rear 10+8pcs
1.9 Steering
a.Power assistance steering
b. Left hand steering control
c. 350 mm steering radius approx
1.10 Brakes
a.Power assisted hydraulic actuation service brakes built into all four wheels
b. Independent dual line system
c. All drum internal expanding
d. Foot-operated engine brake
e. Brake boosters with protection as applicable
f. Automatic drain valve on air tank(s)
g. Mechanical release parking brakes
1.11 Wheels ,Rims&Tires
a.Single front; double rear wheels
b.Good quality heavy-duty on/off road type suitable to full load rating, maximum speed and working conditions
c. Manufacturer's standard rims/ tires must, preferably, meet the following specifications:
i.Tyre size: 11.00 R20,Ridus tire (ALL WHEELS)
ii.Tube tires with flaps preferred
iii.Bias Construction
iv.Ply rating; preferably 16 PR
v.Rim type: Slip-on type with ring locker
vi.Lug type tread pattern
d. . One spare rim with tire mountable on a suitable carrier on each vehicle.
1.12 Cab & Accessories
a.Cab made of steel
b.Three person seating capacity
c.Seats cushioned with weather resistant heavy duty vinyl
d.Seat belts
e.Wide view toughened (Lamina-ted) wind screen
f. Two (2 No.) wipers
g.Floor covering: rubber
h.Horn
i.Tropical ventilation; specify
j.Provide the following:
i.Dual sun visors
ii.Dual rear-view mirrors
iii.Rain gutters/drip mouldings
iv.Container hold-down strap
v In-Cab Pump Switch
vi In-Cab Pneumatic Controller
1.13 Instrumentation
a.Adequate instrumentation to be made up of service indicators as well as advance hazard warning devices. It shall include the following:
i.Fuel gauge
ii.Engine Coolant temperature gauge
iii.Engine oil level gauge
iv.Engine oil pressure gauge
v.Battery charging indicator
vi.Parking brake light
vii.Filters and fuel-water separator service indicators
viii.Speedometer and Odometer
ix.Reversing alarm
x.Engine speed tachometer
xi. Vandalism protection for instrument panel required
1.14 Electric System
a.12 volt system
b. Cab interior lighting
c. Instrument panel lighting
d. Two headlights minimum; high/ low beam
e. Tail/stoplights
f. Direction signal lights for front and rear
g. Reversing light
h. Parking light
i Number plate lights
j Specify the following:
i.AH rating of battery 12V
ii. Ampere rating of alter-nator 100A
iii.KW rating of starter 440CCA
k. Specify other maker's standard ancillaries
i.Model:6-QW-100DF;Capacity:120Min.
ii.Sizie(mm):409×170×209×232
iii.Module:1\4; Terminal:0\1;Mass:18.2kg
1.15 Protective Provision & Finish for Truck Chassis
a.Specify anti-corrosion provi-sions for the truck
b. Final colour finish white.
2: Vacuum Tank Specification
2.1 Principal Features
a. Capacity 8000liters tipping tank, Max Vertical Suction(deepth)≥8m
b. Degree of Vacuum: 80% or above; With an adjustable water pressure valve
c. P.T.O.: 1,500㎏-m~2,000㎏-m;With High Pressure Pump With Indicator of water volume
d. With an automatic release valve to avoid the excess of pressure limit
e. Tank Full loading Time﹤5min
f. Tank Empty unloading Time﹤4min
g. 3 meters deep x 110mm wide is easily achievable.
h. The soil removal process can be carried out wet or dry depending on ground type and process used to agitate ground.
i. Positive and negative displacement Vacuum systems can be used depending on.
j. 250 litre tub, 250 ltr polyurethane onboard water tank.
k.Vacuum Pump
i. Famouns brand (WEILONG)50QZXDH-68/7000 pump
ii. Pressure 7000Pa(93%)
iii. Pump capacity, 352.8m³/hour
iv.Speed at 800rpm
v.Shaft power 5kw
vi.Pump Inlet diameter 50mm
vii. Self-suction depth 8m maximum
l.Tank
i. Tank is made of h Q235 carbon steel thickness 5mm.
ii. Tank nominal Pressure -1.5kpa
iii. Tank capacity 8000liters
iv. High capacity cyclone with 12” full opening lid.
v. Hydraulic full opening rear door assembly with 2 heavy-duty wing clamps.
vi. Full length hydraulic dump subframe with 5ton-80” stoke 2stage cylinder. Rear dump pivot.
Vii: Tanker Dimension(L*W*H)(mm) 5000*1370*1370 appox
m. 2” quick acting brass drain valve (heated) mounted on front head.
n. 2-4” Betts air open/spring close valve.Aluminum camlock fitings.1-6” betts discharge valve.
o. Double acting hydraulic cylinder.
p. 1-6” exhaust and 1-6” intake
q. Oil fillter and sight glass.
r. Hydraulic vibrator assembly on the botton of the tank.
s. Full length 1/8” steel checker plate fenders,1 1/4” tubular handrails, 4 numbered placards, 50’ static ground cable ,toolbox complete with rain lip.
t. Electronic /Hydraulic pendant controls with 25’ of cable or as customer specifications.
u. Many more options available on request.